3920 62 19 00 · Other
Section VII · PLASTICS AND ARTICLES THEREOF; RUBBER AND ARTICLES THEREOF
Lines at this level
- 3920 62 19 05 Poly(ethylene terephthalate) film in rolls: - with a thickness of 0,335 mm or more but not more than 0,365 mm, and - coated with a gold layer with a thickness of 0,03 μm or more but not more than 0,06 μm (declarable code)
- 3920 62 19 08 Poly(ethylene terephthalate) film, not coated with an adhesive, of a thickness of not more than 25 µm, either: - only dyed in the mass, or - dyed in the mass and metallised on one side (declarable code)
- 3920 62 19 28 Non-transparent poly(ethylene terephthalate) film: -each outer layer with a thickness of 7 nm or more but not more than 80 nm, -with a tensile strength of 300 N/cm or more (ASTM D-882), -with a total thickness of 200 µm or more but not more than 350 µm, and -with a width of 600 mm or more but not more than 1 600 mm - covered on one side with a layer of a fluoropolymer, and on the other side with an adhesive and a layer of polyvinylidene difluoride, or coated on both sides with polyvinylidene difluoride or polyvinyl fluoride based on fluorinated polymer composites (declarable code)
- 3920 62 19 32 Transparent poly(ethylene terephthalate) film: -having thickness of both sides of 7 nm or more but not more than 80 nm, or thickness of both sides of 7 µm or more but not more than 80 µm, whether coated with an acrylic-based organic material or not, -with a surface tension of 36 Dyne/cm or more but not more than 39 Dyne/cm, or transparent 3 or 4 layers, second layer of PET, and other layers contain fluorine resin, -with a light transmittance of more than 70 %, -with a haze value of not more than 1,3 %, -with a total thickness of 10 µm or more but not more than 350 µm, -with a width of 800 mm or more but not more than 1 600 mm (declarable code)
- 3920 62 19 38 Poly(ethylene terephthalate) film, of a thickness of not more than 12 µm, coated on one side with a layer of aluminium oxide of a thickness of not more than 35 nm (declarable code)
- 3920 62 19 48 Sheets or rolls of poly(ethylene terephthalate): - coated on both sides with a layer of epoxy acrylic resin, - of a total thickness of 37 μm (± 3 μm) (declarable code)
- 3920 62 19 52 Film of poly(ethylene terephthalate), poly(ethylene naphthalate) or similar polyester, coated on one side with metal and/or metal oxides, containing by weight less than 0,1 % of aluminium, of a thickness of not more than 300 µm and having a surface resistivity of not more than 10 000 ohms (per square) (as determined by the ASTM D 257 method) (declarable code)
- 3920 62 19 60 Poly (ethylene terephtalate) film: - of a thickness of not more than 20 µm, - coated on at least one side with a gas barrier layer consisting of a polymeric matrix in which silica or aluminium oxide has been dispersed and of a thickness of not more than 2µm (declarable code)
- 3920 62 19 70 Poly(ethylene terephthalate) film in rolls with: -a thickness of 35 μm or more, but not more than 75 μm, -a tensile strength of 40 MPa or more in the machine direction (MD) and 200 MPa or more in the transverse direction (TD), -an elongation at break of 400 % or more in MD and 30 % or more in TD, -a heat shrinkage (in water at 90 °C/10s) in MD of 0,49 % or more, but not more than 0,51 %, -a dynamic heat shrinkage (between 55 °C and 70 °C ) in TD of not more than 20 percentage points, -a light transmittance of 85 % or more, -a haze ratio of not more than 6 %, -a surface tension of 38 mN/m or more, -a density of 1,30 g/cm³ or more, but not more than 1,34 g/cm³, -a shelf life declared by the manufacturer of not less than 12 months (declarable code)
- 3920 62 19 79 Reflective film of polyethylene terephthalate, embossed in a pyramidal pattern, with -a thickness of 0.07 mm or more but not more than 0.15 mm -a width of 762 mm or more but not more than 1350 mm (declarable code)
- 3920 62 19 85 Three-layer transparent plastic film consisting of a 15 µm fluorinated polymer (FCC) (EVA) layer, a 275 µm polyethylene terephthalate (PET) layer and a 25 µm fluorinated polymer (FCC) layer with: -a total thickness of 300 µm or more, but not more than 330 µm, -a tensile strength of 375 N/cm or more in both the longitudinal and transverse directions (ASTM D-882), -a low thermal shrinkage of 1 % or less at 150 °C for 30 minutes, -a low water vapor permeability of 2,5 g/m²•d or less, and -a high breakdown voltage of 18 kV or more and -a partial discharge voltage of 1500 VDC or more (BG/T 123542.2-2009) to be used as a protective layer on the back of photovoltaic modules (declarable code)
- 3920 62 19 99 Other (declarable code)
Data as of 2026-11-13.